rust-by-practice/en/src/unsafe/inline-asm.md

# Inline assembly

Rust provides support for inline assembly via the `asm!` macro.
It can be used to embed handwritten assembly in the assembly output generated by the compiler.
Generally this should not be necessary, but might be where the required performance or timing
cannot be otherwise achieved. Accessing low level hardware primitives, e.g. in kernel code, may also demand this functionality.

> **Note**: the examples here are given in x86/x86-64 assembly, but other architectures are also supported.

Inline assembly is currently supported on the following architectures:
- x86 and x86-64
- ARM
- AArch64
- RISC-V

## Basic usage

Let us start with the simplest possible example:

```rust
use std::arch::asm;

unsafe {
    asm!("nop");
}
```

This will insert a NOP (no operation) instruction into the assembly generated by the compiler.
Note that all `asm!` invocations have to be inside an `unsafe` block, as they could insert
arbitrary instructions and break various invariants. The instructions to be inserted are listed
in the first argument of the `asm!` macro as a string literal.

## Inputs and outputs

Now inserting an instruction that does nothing is rather boring. Let us do something that
actually acts on data:

```rust
use std::arch::asm;

let x: u64;
unsafe {
    asm!("mov {}, 5", out(reg) x);
}
assert_eq!(x, 5);
```

This will write the value `5` into the `u64` variable `x`.
You can see that the string literal we use to specify instructions is actually a template string.
It is governed by the same rules as Rust [format strings][format-syntax].
The arguments that are inserted into the template however look a bit different than you may
be familiar with. First we need to specify if the variable is an input or an output of the
inline assembly. In this case it is an output. We declared this by writing `out`.
We also need to specify in what kind of register the assembly expects the variable.
In this case we put it in an arbitrary general purpose register by specifying `reg`.
The compiler will choose an appropriate register to insert into
the template and will read the variable from there after the inline assembly finishes executing.

[format-syntax]: https://doc.rust-lang.org/std/fmt/#syntax

Let us see another example that also uses an input:

```rust
use std::arch::asm;

let i: u64 = 3;
let o: u64;
unsafe {
    asm!(
        "mov {0}, {1}",
        "add {0}, 5",
        out(reg) o,
        in(reg) i,
    );
}
assert_eq!(o, 8);
```

This will add `5` to the input in variable `i` and write the result to variable `o`.
The particular way this assembly does this is first copying the value from `i` to the output,
and then adding `5` to it.

The example shows a few things:

First, we can see that `asm!` allows multiple template string arguments; each
one is treated as a separate line of assembly code, as if they were all joined
together with newlines between them. This makes it easy to format assembly
code.

Second, we can see that inputs are declared by writing `in` instead of `out`.

Third, we can see that we can specify an argument number, or name as in any format string.
For inline assembly templates this is particularly useful as arguments are often used more than once.
For more complex inline assembly using this facility is generally recommended, as it improves
readability, and allows reordering instructions without changing the argument order.

We can further refine the above example to avoid the `mov` instruction:

```rust
use std::arch::asm;

let mut x: u64 = 3;
unsafe {
    asm!("add {0}, 5", inout(reg) x);
}
assert_eq!(x, 8);
```

We can see that `inout` is used to specify an argument that is both input and output.
This is different from specifying an input and output separately in that it is guaranteed to assign both to the same register.

It is also possible to specify different variables for the input and output parts of an `inout` operand:

```rust
use std::arch::asm;

let x: u64 = 3;
let y: u64;
unsafe {
    asm!("add {0}, 5", inout(reg) x => y);
}
assert_eq!(y, 8);
```

## Late output operands

The Rust compiler is conservative with its allocation of operands. It is assumed that an `out`
can be written at any time, and can therefore not share its location with any other argument.
However, to guarantee optimal performance it is important to use as few registers as possible,
so they won't have to be saved and reloaded around the inline assembly block.
To achieve this Rust provides a `lateout` specifier. This can be used on any output that is
written only after all inputs have been consumed.
There is also a `inlateout` variant of this specifier.

Here is an example where `inlateout` *cannot* be used:

```rust
use std::arch::asm;

let mut a: u64 = 4;
let b: u64 = 4;
let c: u64 = 4;
unsafe {
    asm!(
        "add {0}, {1}",
        "add {0}, {2}",
        inout(reg) a,
        in(reg) b,
        in(reg) c,
    );
}
assert_eq!(a, 12);
```

Here the compiler is free to allocate the same register for inputs `b` and `c` since it knows they have the same value. However it must allocate a separate register for `a` since it uses `inout` and not `inlateout`. If `inlateout` was used, then `a` and `c` could be allocated to the same register, in which case the first instruction to overwrite the value of `c` and cause the assembly code to produce the wrong result.

However the following example can use `inlateout` since the output is only modified after all input registers have been read:

```rust
use std::arch::asm;

let mut a: u64 = 4;
let b: u64 = 4;
unsafe {
    asm!("add {0}, {1}", inlateout(reg) a, in(reg) b);
}
assert_eq!(a, 8);
```

As you can see, this assembly fragment will still work correctly if `a` and `b` are assigned to the same register.

## Explicit register operands

Some instructions require that the operands be in a specific register.
Therefore, Rust inline assembly provides some more specific constraint specifiers.
While `reg` is generally available on any architecture, explicit registers are highly architecture specific. E.g. for x86 the general purpose registers `eax`, `ebx`, `ecx`, `edx`, `ebp`, `esi`, and `edi` among others can be addressed by their name.

```rust,no_run
use std::arch::asm;

let cmd = 0xd1;
unsafe {
    asm!("out 0x64, eax", in("eax") cmd);
}
```

In this example we call the `out` instruction to output the content of the `cmd` variable to port `0x64`. Since the `out` instruction only accepts `eax` (and its sub registers) as operand we had to use the `eax` constraint specifier.

> **Note**: unlike other operand types, explicit register operands cannot be used in the template string: you can't use `{}` and should write the register name directly instead. Also, they must appear at the end of the operand list after all other operand types.

Consider this example which uses the x86 `mul` instruction:

```rust
use std::arch::asm;

fn mul(a: u64, b: u64) -> u128 {
    let lo: u64;
    let hi: u64;

    unsafe {
        asm!(
            // The x86 mul instruction takes rax as an implicit input and writes
            // the 128-bit result of the multiplication to rax:rdx.
            "mul {}",
            in(reg) a,
            inlateout("rax") b => lo,
            lateout("rdx") hi
        );
    }

    ((hi as u128) << 64) + lo as u128
}
```

This uses the `mul` instruction to multiply two 64-bit inputs with a 128-bit result.
The only explicit operand is a register, that we fill from the variable `a`.
The second operand is implicit, and must be the `rax` register, which we fill from the variable `b`.
The lower 64 bits of the result are stored in `rax` from which we fill the variable `lo`.
The higher 64 bits are stored in `rdx` from which we fill the variable `hi`.

## Clobbered registers

In many cases inline assembly will modify state that is not needed as an output.
Usually this is either because we have to use a scratch register in the assembly or because instructions modify state that we don't need to further examine.
This state is generally referred to as being "clobbered".
We need to tell the compiler about this since it may need to save and restore this state around the inline assembly block.

```rust
use core::arch::asm;

fn main() {
    // three entries of four bytes each
    let mut name_buf = [0_u8; 12];
    // String is stored as ascii in ebx, edx, ecx in order
    // Because ebx is reserved, we get a scratch register and move from
    // ebx into it in the asm.  The asm needs to preserve the value of
    // that register though, so it is pushed and popped around the main asm
    // (in 64 bit mode for 64 bit processors, 32 bit processors would use ebx)

    unsafe {
        asm!(
            "push rbx",
            "cpuid",
            "mov [{0}], ebx",
            "mov [{0} + 4], edx",
            "mov [{0} + 8], ecx",
            "pop rbx",
            // We use a pointer to an array for storing the values to simplify
            // the Rust code at the cost of a couple more asm instructions
            // This is more explicit with how the asm works however, as opposed
            // to explicit register outputs such as `out("ecx") val`
            // The *pointer itself* is only an input even though it's written behind
            in(reg) name_buf.as_mut_ptr(),
            // select cpuid 0, also specify eax as clobbered
            inout("eax") 0 => _,
            // cpuid clobbers these registers too
            out("ecx") _,
            out("edx") _,
        );
    }

    let name = core::str::from_utf8(&name_buf).unwrap();
    println!("CPU Manufacturer ID: {}", name);
}
```

In the example above we use the `cpuid` instruction to read the CPU manufacturer ID.
This instruction writes to `eax` with the maximum supported `cpuid` argument and `ebx`, `esx`, and `ecx` with the CPU manufacturer ID as ASCII bytes in that order.

Even though `eax` is never read we still need to tell the compiler that the register has been modified so that the compiler can save any values that were in these registers before the asm. This is done by declaring it as an output but with `_` instead of a variable name, which indicates that the output value is to be discarded.

This code also works around the limitation that `ebx` is a reserved register by LLVM. That means that LLVM assumes that it has full control over the register and it must be restored to its original state before exiting the asm block, so it cannot be used as an output. To work around this we save the register via `push`, read from `ebx` inside the asm block into a temporary register allocated with `out(reg)` and then restoring `ebx` to its original state via `pop`. The `push` and `pop` use the full 64-bit `rbx` version of the register to ensure that the entire register is saved. On 32 bit targets the code would instead use `ebx` in the `push`/`pop`.

This can also be used with a general register class (e.g. `reg`) to obtain a scratch register for use inside the asm code:

```rust
use std::arch::asm;

// Multiply x by 6 using shifts and adds
let mut x: u64 = 4;
unsafe {
    asm!(
        "mov {tmp}, {x}",
        "shl {tmp}, 1",
        "shl {x}, 2",
        "add {x}, {tmp}",
        x = inout(reg) x,
        tmp = out(reg) _,
    );
}
assert_eq!(x, 4 * 6);
```

## Symbol operands and ABI clobbers

By default, `asm!` assumes that any register not specified as an output will have its contents preserved by the assembly code. The [`clobber_abi`] argument to `asm!` tells the compiler to automatically insert the necessary clobber operands according to the given calling convention ABI: any register which is not fully preserved in that ABI will be treated as clobbered.  Multiple `clobber_abi` arguments may be provided and all clobbers from all specified ABIs will be inserted.

[`clobber_abi`]: ../../reference/inline-assembly.html#abi-clobbers

```rust
use std::arch::asm;

extern "C" fn foo(arg: i32) -> i32 {
    println!("arg = {}", arg);
    arg * 2
}

fn call_foo(arg: i32) -> i32 {
    unsafe {
        let result;
        asm!(
            "call *{}",
            // Function pointer to call
            in(reg) foo,
            // 1st argument in rdi
            in("rdi") arg,
            // Return value in rax
            out("rax") result,
            // Mark all registers which are not preserved by the "C" calling
            // convention as clobbered.
            clobber_abi("C"),
        );
        result
    }
}
```

## Register template modifiers

In some cases, fine control is needed over the way a register name is formatted when inserted into the template string. This is needed when an architecture's assembly language has several names for the same register, each typically being a "view" over a subset of the register (e.g. the low 32 bits of a 64-bit register).

By default the compiler will always choose the name that refers to the full register size (e.g. `rax` on x86-64, `eax` on x86, etc).

This default can be overriden by using modifiers on the template string operands, just like you would with format strings:

```rust
use std::arch::asm;

let mut x: u16 = 0xab;

unsafe {
    asm!("mov {0:h}, {0:l}", inout(reg_abcd) x);
}

assert_eq!(x, 0xabab);
```

In this example, we use the `reg_abcd` register class to restrict the register allocator to the 4 legacy x86 registers (`ax`, `bx`, `cx`, `dx`) of which the first two bytes can be addressed independently.

Let us assume that the register allocator has chosen to allocate `x` in the `ax` register.
The `h` modifier will emit the register name for the high byte of that register and the `l` modifier will emit the register name for the low byte. The asm code will therefore be expanded as `mov ah, al` which copies the low byte of the value into the high byte.

If you use a smaller data type (e.g. `u16`) with an operand and forget the use template modifiers, the compiler will emit a warning and suggest the correct modifier to use.

## Memory address operands

Sometimes assembly instructions require operands passed via memory addresses/memory locations.
You have to manually use the memory address syntax specified by the target architecture.
For example, on x86/x86_64 using Intel assembly syntax, you should wrap inputs/outputs in `[]` to indicate they are memory operands:

```rust
use std::arch::asm;

fn load_fpu_control_word(control: u16) {
    unsafe {
        asm!("fldcw [{}]", in(reg) &control, options(nostack));
    }
}
```

## Labels

Any reuse of a named label, local or otherwise, can result in an assembler or linker error or may cause other strange behavior. Reuse of a named label can happen in a variety of ways including:

-   explicitly: using a label more than once in one `asm!` block, or multiple times across blocks.
-   implicitly via inlining: the compiler is allowed to instantiate multiple copies of an `asm!` block, for example when the function containing it is inlined in multiple places.
-   implicitly via LTO: LTO can cause code from *other crates* to be placed in the same codegen unit, and so could bring in arbitrary labels.

As a consequence, you should only use GNU assembler **numeric** [local labels] inside inline assembly code. Defining symbols in assembly code may lead to assembler and/or linker errors due to duplicate symbol definitions.

Moreover, on x86 when using the default Intel syntax, due to [an LLVM bug], you shouldn't use labels exclusively made of `0` and `1` digits, e.g. `0`, `11` or `101010`, as they may end up being interpreted as binary values. Using `options(att_syntax)` will avoid any ambiguity, but that affects the syntax of the _entire_ `asm!` block. (See [Options](#options), below, for more on `options`.)

```rust
use std::arch::asm;

let mut a = 0;
unsafe {
    asm!(
        "mov {0}, 10",
        "2:",
        "sub {0}, 1",
        "cmp {0}, 3",
        "jle 2f",
        "jmp 2b",
        "2:",
        "add {0}, 2",
        out(reg) a
    );
}
assert_eq!(a, 5);
```

This will decrement the `{0}` register value from 10 to 3, then add 2 and store it in `a`.

This example shows a few things:

- First, that the same number can be used as a label multiple times in the same inline block.
- Second, that when a numeric label is used as a reference (as an instruction operand, for example), the suffixes “b” (“backward”) or ”f” (“forward”) should be added to the numeric label. It will then refer to the nearest label defined by this number in this direction.

[local labels]: https://sourceware.org/binutils/docs/as/Symbol-Names.html#Local-Labels
[an LLVM bug]: https://bugs.llvm.org/show_bug.cgi?id=36144

## Options

By default, an inline assembly block is treated the same way as an external FFI function call with a custom calling convention: it may read/write memory, have observable side effects, etc. However, in many cases it is desirable to give the compiler more information about what the assembly code is actually doing so that it can optimize better.

Let's take our previous example of an `add` instruction:

```rust
use std::arch::asm;

let mut a: u64 = 4;
let b: u64 = 4;
unsafe {
    asm!(
        "add {0}, {1}",
        inlateout(reg) a, in(reg) b,
        options(pure, nomem, nostack),
    );
}
assert_eq!(a, 8);
```

Options can be provided as an optional final argument to the `asm!` macro. We specified three options here:
- `pure` means that the asm code has no observable side effects and that its output depends only on its inputs. This allows the compiler optimizer to call the inline asm fewer times or even eliminate it entirely.
- `nomem` means that the asm code does not read or write to memory. By default the compiler will assume that inline assembly can read or write any memory address that is accessible to it (e.g. through a pointer passed as an operand, or a global).
- `nostack` means that the asm code does not push any data onto the stack. This allows the compiler to use optimizations such as the stack red zone on x86-64 to avoid stack pointer adjustments.

These allow the compiler to better optimize code using `asm!`, for example by eliminating pure `asm!` blocks whose outputs are not needed.

See the [reference](../../reference/inline-assembly.html) for the full list of available options and their effects.